RANE HAL3s Digital Multiprocessor
The RANE HAL3s is a digital processor for audio systems. This groundbreaking architecture is used for room combining, paging and distributing audio to several zones in an installation. Utilizing Halogen® software, even novice users are guided through what used to be complex tasks in just minutes. No intricate matrix mixing or presets are required for room combining and paging. No complex wiring is required to distribute pages and background music to multiple zones. Seamlessly interface HAL to small or large installations with web controls, (no app required) and/or a broad variety of peripheral devices including smart Digital Remotes (DRs), Remote Audio Devices (RADs), portable or rack automixers, small remote amplifiers, and an advanced Paging Station. In addition, the HAL3s Multiprocessor and Halogen™ software check the status, location, CAT 5e wiring integrity, and that audio is flowing in all peripheral devices, so you know your system is properly connected and ready to go.
Features
- - 6-in 10-out system: 2x6 analog & 4x4 expansion (via RAD ports)
- - 2 Mic/Line, Line-plus inputs with 48V phantom power
- - Supports up to 2 remote audio devices (RADs) and 2 digital remotes (DRs) or 4 digital remotes (DRs)
- - 4 logic inputs for contact closure control
- - Front panel signal and overload indicators
- - Supports control via web browser
- - Event manager for time-of-day event control
- - 108dB dynamic range
Package Contents
- - HAL3s
- - Euroblock connectors
- - Cat-5e cable
- - IEC power cable
Technical Specifications
Parameter | Specification | Limit | Conditions/Comments |
Analog I/O | 2 x 6 | 2 Mic/Line/Line-plus Inputs, 6 Line Outputs | |
Connectors | Euroblock | 4 x 6-pin, 5mm pitch, Green = Inputs, Orange = Outputs | |
CODEC | 24-bit, 48kHz | ||
All Inputs | Common specifications | ||
Input Impedance | 2.9kΩ | 1% | Each leg to ground |
Inter-channel isolation | >100dB | typ | 20Hz–20kHz, unity gain, channel-to-channel |
CMRR | 55dB | min | 1kHz |
Inputs: Dynamic Mic Mode | Active Balanced | Microphone input mode without phantom power | |
Gain | +30dB to +50dB | typ | +30db (analog gain), 1dB steps to +50dB (digital gain) |
THD+N | < 0.005% | typ | 20Hz–20kHz, +4dBu out, 0dB digital gain |
Equivalent Input Noise | -120dBu | typ | 20Hz–20kHz, 150Ω source, 30dB gain |
Maximum Input | -18dBV (125mVrms) | typ | 1kHz, < 0.01% THD+N |
Frequency Response | 20Hz–20kHz, +0.0/-0.3dB | +4dBu out, 100kΩ load, Mic Input to Output | |
Inputs: Condenser Mic Mode | Active Balanced | Microphone input mode with 48V phantom power | |
Gain | +18dB to +38dB | typ | +18dB (analog gain), 1dB steps to +38dB (digital gain) |
Phantom Power | +48VDC | 10mA max per input | |
THD+N | < 0.005% | typ | 20Hz–20kHz, +4dBu out, 0dB digital gain |
Equivalent Input Noise | -110dBu | typ | 20Hz–20kHz, 150Ω source, 18dB gain |
Maximum Input | -6dBV (500mVrms) | typ | 1kHz, < 0.01% THD+N |
Frequency Response | 20Hz–20kHz, +0.0/-0.3dB | +4dBu out, 100kΩ load, Mic Input to Output | |
Inputs: Line+ Mode | Active Summer | Left ("+") and Right ("-") signals summed to mono | |
Gain | 0dB to +20dB | typ | 0dB (analog gain), 1dB steps to +20dB (digital gain) |
THD+N | < 0.007 % | typ | 20Hz–20kHz, +4dBu out, 0dB digital gain |
Maximum Input | +14dBu | typ | 1kHz, < 0.01% THD+N, each leg |
Frequency Response | 20Hz–20kHz, +0.0/-0.3dB | +4dBu out, 100kΩ load, Line-plus Input to Output | |
Dynamic Range (in to out) | 108dB | max | re +20dBu, 20kHz BW, A weighted, Rs = 50Ω |
Inputs: Line Mode | Active Balanced | Balanced line level input | |
Gain | 0dB | typ | 0dB (analog gain), 1dB steps to +20dB (digital gain) |
THD+N | < 0.005% | typ | 20Hz–20kHz, +4dBu out, 0dB digital gain |
Maximum Input | +14dBu | typ | 1kHz, < 0.01% THD+N |
Frequency Response | 20Hz–20kHz, +0.0/-0.3dB | +4dBu out, 100kΩ load, Line Input to Output | |
Dynamic Range (in to out) | 108dB | max | re +20dBu, 20kHz BW, A weighted, Rs = 50Ω |
Outputs | Active Balanced | ||
Impedance | 200Ω | 1% | Each leg |
Maximum Output | +20.0/+15.5dBu | typ | 1kHz, 100kΩ/600Ω load |
Indicators | |||
Signal | -50dBFS | typ | Green LED, peak-reading |
Overload | -0.5dBFS | typ | Red LED, peak-reading |
Propagation Delays | |||
RAD In to RAD Out | 1.71ms | typ | Tested with RAD23 |
RAD In to Analog Out | 1.85ms | typ | |
Analog In to RAD Out | 2.25ms | typ | |
Analog In to Analog Out | 2.39ms | typ | |
DSP | |||
Processing Power | 2400MIPS | max | 1DSP @ 300MHz with up to 8 instructions/cycle |
Word Length | 32/64-bit Floating Point | ||
Delay Memory | 20 seconds | max | |
Computer Interface | |||
Type | Ethernet 1000 Base-T | Zeroconf service discovery protocol for easy set up | |
Cable | Shielded CAT 5e or better | RJ-45 connector | |
Length | 100 meters/300 feet | max | Standard Ethernet cable length limit |
RAD Port | 2 | RJ-45 connectors | |
Audio Channels | 2 in x 2 out | Each port 2 in x 2 out, control channel, 24-bit, 48kHz | |
Power | 24VDC @ 100mA | max | Each port |
Length | 152 meters / 500 feet | max | Shielded CAT 5e cable or better |
DR Ports | 4 | RJ-45 connectors | |
Power | 24VDC @ 50mA | max | Each port |
Length | 300 meters / 1000 feet | max | Shielded CAT 5e cable or better |
Logic Inputs | 4 | ||
Connector | Mini Euroblock | 6-pin, 3.81mm pitch, Black | |
Internal Pull-up | 51.1kΩ, 5.0V | Protected to +24V, reverse polarity protected | |
Vin High | > 2.2V | min | Normal state |
Vin Low | < 0.7V | max | External circuit sinks > 22µA to assert |
Wiring | Class 2 | All rear panel terminals | |
Power Requirement | 100 to 240VAC | 50/60Hz, 20W max | |
Ambient Room Temp. | 40°C | max | Maximum external loading |
Unit: Conformity | CE, FCC, cCSAus | ||
Unit: Size | 1.73"H x 19"W x 8.25"D | (4.4cm x 48.3cm x 20.9cm) | |
Weight | 4.75 lb. | (2.2 kg) | |
Shipping: Size | 4.25" x 20.3" x 13.75" | (11cm x 52cm x 35cm) | |
Weight | 9 lb. | (3.8 kg) |